My 3GPP 23.501 Notes
My 3GPP 23.501 Notes
Definition and abbreviations
See My 3GPP definition notes for definitions
See My 3GPP abbreviation notes for abbreviations
§ 5.2.1 General
Network access is the means for user to connect to 5G Core Network (CN). Network access control comprises the following functionality:
- Network selection,
- Identification and authentication,
- Authorization,
- Access control and barring,
- Policy control,
- Lawful Interception.
§ 5.2.2 Network Selection
To determine which PLMN to attempt registration, UE performs network selection. The network selection procedure comprises two main parts, PLMN selection and access network (AN) selection. The requirements for PLMN selection are specified in TS 22.011 and the procedures are in TS 23.122. The access network (AN) selection part for the 3GPP access networks is specified in TS 36.300 for E-UTRAN and in TS 38.300 for the NR. The network selection for Disaster Roaming is described in TS 23.122 and TS 24.501.
§ 5.2.3 Identification and authentication
The network may authenticate the UE during any procedure establishing a NAS signalling connection with the UE. The security architecture is specified in TS 33.501. The network may optionally perform an PEI check with 5G-EIR.
§ 5.2.4 Authorization
The authorization for connectivity of the subscriber to the 5GC and the authorization for the services that the user is allowed to access based on subscription (e.g. Operator Determined Barring, Roaming restrictions, Access Type and RAT Type currently in use) is evaluated once the user is successfully identified and authenticated. This authorization is executed during UE Registration procedure.
§ 5.2.5 Access control and barring see spec
§ 5.2.6 Policy control
Network access control including service authorization may be influenced by Policy control, as specified in clause 5.14.
§ 5.2.7 Lawful Interception
For definition and functionality of Lawful Interception, see TS 33.126.
§ 5.4.7 NG-RAN location reporting
NG-RAN supports the NG-RAN location reporting for the services that require accurate cell identification (e.g. emergency services, lawful intercept, charging) or for the UE mobility event notification service subscribed to the AMF by other NFs. The NG-RAN location reporting may be used by the AMF when the target UE is in CM-CONNECTED state. The NG-RAN location reporting may be used by the AMF to determine the geographically located TAI in the case of NR satellite access.
The AMF may request the NG-RAN location reporting with event reporting type (e.g. UE location or UE presence in Area of Interest), reporting mode and its related parameters (e.g. number of reporting).
If the AMF requests UE location, the NG-RAN reports the current UE location (or last known UE location with time stamp if the UE is in RRC Inactive state) based on the requested reporting parameter (e.g. one-time reporting or continuous reporting).
If the AMF requests UE location, in the case of NR satellite access, the NG-RAN provides all broadcast TAIs to the AMF as part of the ULI. The NG-RAN also reports the TAI where the UE is geographically located if this TAI can be determined.
If the AMF requests UE presence in the Area Of Interest, the NG-RAN reports the UE location and the indication (i.e. IN, OUT or UNKNOWN) when the NG-RAN determines the change of UE presence in Area Of Interest. After N2 based Handover, if the NG-RAN location reporting information is required, the AMF shall re-request the NG-RAN location reporting to the target NG-RAN node. For Xn based Handover, the source NG-RAN shall transfer the requested NG-RAN location reporting information to target NG-RAN node.
The AMF requests the location information of the UE either through independent N2 procedure (i.e. NG-RAN location reporting as specified in clause 4.10 of TS 23.502), or by including the request in some specific N2 messages as specified in TS 38.413.